Proface LM4201TADAC PFXLM4201TADAC Touchscreen Film

Order each part separately is available

Be aware of the following items when building the LM4201TADAC PFXLM4201TADAC Front Overlay Touch Membrane LT into an end-use product:
• The LT unit's rear face is not approved as an enclosure. When building the LT unit into an end-use product, be sure to use an enclosure that satisfies standards as the end-use product's overall enclosure.
• The LM4201TADAC PFXLM4201TADAC Touchscreen Panel Protective Film LT unit must be used indoors only.
• Install and operate the LM4201TADAC PFXLM4201TADAC Touch Panel Overlay LT with its front panel facing outwards.
• If the LT is mounted so as to cool itself naturally, be sure to install it in a vertical panel. Also, it's recommended that the LT should be mounted at least 100 mm away from any other adjacent structures or machine parts. The temperature must be checked on the final product in which the LT is installed.
• For use on a flat surface of a Type 4X (Indoor Use Only) and/or Type 13 Enclosure.

VICPAS supply Pro-face LT4000M Series LM4201TADAC PFXLM4201TADAC Protective Film and Touch Screen Panel with 365 days warranty and support Urgent Worldwide Shipping. The following rules must be applied when wiring a LM4201TADDC PFXLM4201TADDC Touch Membrane Protective Film LT:
 Input/Output and communication wiring must be kept separate from the power wiring. Route these 2 types of wiring in separate cable ducting.
 Verify that the operating conditions and environment are within specification.
 Use proper wire sizes to meet voltage and current requirements.
 Use copper conductors.
 Use twisted-pair, shielded cables for analog, and/or fast Input/Output.
 Use twisted-pair, shielded cables for networks, and fieldbus.
 For the power connector, refer to DC power supply wiring diagram.
 When terminals A2 and B2 (signal name: Q1, Q0) are wired to external I/O, use the same power source for external I/O and the LM4201TADDC PFXLM4201TADDC Front Overlay HMI Panel Glass LT. Refer to Power Supply Connections.
 If you use a temperature sensor with thermocouple inputs, make sure you use the compensation cable.
 Prevent temperature changes to the thermocouple connection terminal. Correct temperature measurement may not be possible if the thermocouple cold junction (LT's thermocouple compensation wiring to the connection terminal) experiences temperature changes.

Specifications:

The table below describes the parameters of the Proface LT4000M LM4201TADAC PFXLM4201TADAC Touch Screen Monitor Front Overlay HMI Machine.

Related Proface LT4000M Series HMI Part No. :

Pro-face LT4000M	Description	Inventory status
LM4201TADAC	Pro-face LT4000M HMI Panel Glass Protective Film	Available Now
LM4201TADAK	Proface LT4000M Front Overlay Touch Screen Monitor	In Stock
LM4201TADDC	Proface LT4000M Touch Screen Protective Film Replacement	In Stock
LM4201TADDK	Proface LT4000M Protective Film Touch Panel Repair	Available Now
LM4301TADAC	Proface LT4000M Protective Film Touchscreen Repair	In Stock
LM4301TADAK	Proface LT4000M HMI Touch Screen Glass Protective Film	Available Now
LM4301TADDC	Proface LT4000M Touch Screen Panel Front Overlay Repair	In Stock
LM4301TADDK	Pro-face LT4000M Front Overlay Touch Membrane	In Stock
Proface LT4000M	Description	Inventory status

Proface LT4000M Series HMI Manuals PDF Download:

LT4000M 3.5 in. Datasheet

LT4000M 5.7 in. Datasheet

LT-4201TM LT-4301TM Hardware Manual

LT-4201TM LT-4301TM Installation Guide

PFXLM4201TADDC Specifications

Common Misspellings: 

LM4201TADAC PFXLM4201TDAC
LM4201TADA PFXLM4201TADAC
LM420T1ADAC PFXLM4201TADAC
LM4201TADAC PFXLM42O1TADAC
LM4201TADAC PFXLM42011TADAC