Keyence VT3-Q5S Front Overlay Touch Glass Repair
Keyence VT3-Q5S Front Overlay Touch Glass Repair
Keyence VT3-Q5S Front Overlay Touch Glass Repair
Keyence VT3-Q5S Front Overlay Touch Glass Repair
Model
VT3-Q5S

Item specifics

Brand
Keyence
Size
5 inch
Warranty
365 Days
Product Line
Keyence VT3
Supply
VT3-Q5S Front Overlay Touch Digitizer Glass
Shipping
2-4 workdays

Review

Description

Keyence VT3 VT3-Q5S Touch Screen Protective Film Repair Replacement

Order each part separately is available

Keyence VT3-Q5S Touch Screen Protective Film Repair Replacement

Ambient temperature/humidity precautions
Pay attention to the following points when installing the VT3-Q5S Touch Panel Overlay VT3 product inside a control panel.
• When the ambient temperature is higher than 40°C, please use it at a maximum absolute humidity of 85% RH at 40°C.
• Do not install VT3-Q5S Front Overlay Touchscreen Protective Film Touch Screen Glass VT3 in a location where the ambient temperature exceeds the 0 to 50°C, or the ambient humidity exceeds the 35 to 85% RH range.
• If the ambient temperature exceeds the above range, install a forced air cooling fan or air conditioner to keep the ambient temperature within this range.
• Allow as much space as possible between VT3-Q5S HMI Panel Glass Protective Film VT3 and surrounding structures and other components to improve maintainability, operability and ventilation.
• Do not mount the VT3-Q5S Touch Digitizer Front Overlay VT3 directly above equipment (e.g. heaters, transformers, inverters and equipment with large resistance) that generate lots of heat.
• Do not use PORT1 (USB) in locations that are subject to vibration or impact. The USB connector is not provided with a locking function, so the USB cable may become loose or disconnected, and disrupt communications.



Specifications:

The table below describes the parameters of the Keyence VT3 VT3-Q5S Touch Digitizer Protective Film HMI Parts.

Cooling Method: Natural air circulation
Backlight: LED Back Light
Brand: Keyence
Product Line: Keyence VT3
Touch Size: 5"
Display Colors: 32,768 Colors
Display Type: TFT LCD
Operation Temp.: 0 °C ~ 50 °C
Resolution: 320 x 240 pixels
Warranty: 12-Month Warranty


Related Keyence VT3 Series Part No. :

Keyence VT3 HMI Description Inventory status
VT3-V7R Keyence VT3 Series Touch Screen Front Overlay Repair In Stock
VT3-V8 Keyence VT3 Series Protective Film Touch Panel Replacement Available Now
VT3-V10 Keyence VT3 Series Touch Digitizer Front Overlay Repair In Stock
VT3-V10D Keyence VT3 Series Protective Film HMI Touch Screen Replacement In Stock
VT3-W4G Keyence VT3 Series Front Overlay HMI Panel Glass Repair Available Now
VT3-W4GA Keyence VT3 Series Touch Membrane Protective Film Replacement In Stock
VT3-W4M Keyence VT3 Series Touchscreen Glass Front Overlay Repair Available Now
VT3-W4MA Keyence VT3 Series Protective Film Touch Panel Replacement In Stock
VT3-W4T Keyence VT3 Series Front Overlay HMI Touch Glass Repair Available Now
VT3-W4TA Keyence VT3 Series Touch Screen Protective Film Replacement In Stock
VT3-X15 Keyence VT3 Series Front Overlay Touch Digitizer Repair In Stock
VT3-X15D Keyence VT3 Series Protective Film Touch Membrane Replacement In Stock
Keyence VT3 Series Description Inventory status


Keyence VT3 Series HMI Manuals PDF Download:

  • VT3 Series Hardware Manual
  • VT3-V6H_Datasheet
  • VT3-V7 Datasheet
  • VT3-V8_Datasheet

  • FAQ:

    Question: What is the panel thickness?

    Answer:
    What is the panel thickness?
    Attention: VT3-V6H(G)/Q5H(G)/V7R cannot be mounted in the panel.


    Question: What are the precautions to observe during grounding?

    Answer:
    • The ground terminal of VT3-X15/S12/S10/V10 and shielding wire of the VT3-V6H(G)/Q5H(G), VT-T1, VT3-V7R switch unit(VT3-SW4/SW6)should be separately grounded. D-type grounding (third grounding)is used, with a grounding resistance below 100Ω.
    • If an exclusive ground cannot be obtained, share the ground with another device.
    • Use a cable of nominal cross-section 2mm or thicker as the grounding cable.
    • Keep the grounding point as close as possible to the VT3, and keep the ground lead as short as possible.
    • If the ground lead must be extended, use thick insulating cable and pass the ground lead through a duct before grounding.
    • In VT3-V6H(G)/Q5H(G), if FG1 (power panel shielding)and FG2(RS-232/422 shielding)exist on the connecting cable, grounding must be made separately.
    • In VT-T1, shielding wire must be used on the terminal block (button switch/start switch/functional switch connection)and Ethernet port, and must be grounded.
    • The shielding wire of the VT3-V7R Main Unit cable should be grounded at the power FG terminal.

    Common misspellings: 

    V3-Q5S
    VT3-5S
    VT33-Q5S
    VT-3Q5S
    VT3-5QS