Nidec Corp UNI2403 3847-1120-07 Control Housing Repair
- Model
- UNI2403 3847-1120-07
Item specifics
- Brand
- Nidec Corp
- Warranty
- 365 Days
- Supply
- Nidec Corp UNI2403 3847-1120-07 Control HMI Case
- Part Number
- UNI2403 3847-1120-07
- Shipping
- 2-4 workdays
Review
Description
Nidec Corp UNI2403 3847-1120-07 Control Housing Repair Replacement
VICPAS supplies Nidec Corp UNI2403 3847-1120-07 Control Plastic Case with 365 days warranty and supports Urgent Worldwide Shipping. These electronic drive products are intended to be used with appropriate motors, controllers, electrical protection components and other equipment to form complete end products or systems. Compliance with safety and EMC regulations depends upon installing and configuring drives correctly, including using the specified input filters. The Nidec Corp UNI2403 3847-1120-07 Control Plastic Shell drives must be installed only by professional assemblers who are familiar with requirements for safety and EMC.
The Nidec Corp UNI2403 3847-1120-07 Control Plastic Cover drive is intended as a component for professional incorporation into complete equipment or a system. If installed incorrectly, the drive may present a safety hazard. The drive uses high voltage and currents, carries a high level of stored electrical energy, and is used to control equipment that can cause injury.
Close attention is required to the electrical installation and the system design to avoid hazards, either in normal operation or in the event of equipment malfunction.
Specifications:
The table below describes the parameters of the Nidec Corp UNI2403 3847-1120-07 Control Enclosure HMI Parts.
| Default Function: | Frequency/Speed Reference |
| Input Voltage: | 12/24 V dc ±20% |
| Input Resistance: | 100kΩ |
| Voltage Range: | 0V to +24V |
| Voltage Tolerance: | ±10% |
| Brand: | Nidec Corp |
| Contact Condition: | Normally open |
| Noise Voltage: | 1500 V p-p |
| Update Period: | 8ms |
| Warranty: | 365 Days |
Related HMI Part No. :
| HMI Replacement Part | Description | Inventory status |
| DTS640480-000 DU30 | DTS640480-000 DU30 HMI Touch Screen Glass Replacement | Available Now |
| DSC01361 | DSC01361 Touch Screen Panel Replacement Repair | In Stock |
| CALDARO AB I401-8121 | CALDARO AB I401-8121 Touch Membrane Repair Replacement | In Stock |
| BC42611854 | BC42611854 Touch Glass Replacement Repair | In Stock |
| B070N18AG04-02 E217342 | B070N18AG04-02 E217342 Touch Digitizer Glass Repair | Available Now |
| 1042DF12 | 1042DF12 HMI Panel Glass Replacement Repair | Available Now |
| A1016C-32 S130521-5080 | A1016C-32 S130521-5080 Touch Screen Monitor Replacement | In Stock |
| UNI2403 3847-878803 | UNI2403 3847-878803 Side Cover Replacement | In Stock |
| UNI2403 3847-1120-07 | UNI2403 3847-1120-07 Control Housing Replacement Repair | Available Now |
| HMI Repair Part | Description | Inventory status |
Nidec Corp UNI2403 3847-1120-07 Control Manuals PDF Download:
FAQ:
Question: How to choose a Mounting Location?
Answer:
Remove terminal covers, as follows:
1. Working on either side of the terminal cover, push the inner edge of the cover firmly outward until it becomes unclipped.
2. Swing the side of the cover outward and upward until the remaining clips become released.
3. Remove the gland plate
Question: How to remove the three terminal covers on the Size 5 power module？
Answer:
Remove the three terminal covers on the power module, as follows:
1. Remove the two posidrive screws.
2. Remove the upper cover.
3. Remove the two posidrive screws.
4. Remove the lower cover until it is released from the middle cover.
5. Remove the four screws that are now revealed.
6. Remove the middle cover.
All the power terminals and ribbon-cable connectors are now accessible.
Common misspellings:
Nidec Corp UNI2403 387-1120-07Nidec Corp UNI2403 3847-112-07
Nidec Corp NUI2403 3847-1120-07
Nidec Corp UNI24o3 3847-1120-07
Nidec Corp UNI2403 3847-11200-07
